- #PMDG 777 COLD AND DARK INSTALL#
- #PMDG 777 COLD AND DARK DRIVER#
- #PMDG 777 COLD AND DARK PRO#
- #PMDG 777 COLD AND DARK PLUS#
I will try uninstalling and reinstalling DirectX and the vc++ runtimes and see if that helps. I was advised by PMDG that FSUIPC might be able o trap the g2d.dll errors like was done for FSX g3d.dll errors.
![pmdg 777 cold and dark pmdg 777 cold and dark](http://c-aviation.net/wp-content/uploads/2015/10/777-startup.jpg)
I have also flown the P3d default aircraft between NZAA and NZQN without any issue. I am now out of options and reaching out for your assistance. I rebooted the computer, and tried another PFPX based route with 777LR or ER Autopilot and on queue, 1 minute into the flight got a CTD with the gtd.dll error. I did the above for both 777LR and 777300ER without issue. Even after secure parking I was able to pan around the aircraft with no VAS warning alarms of any sort. Not a single CTD irrespective of moving to spot view every now and then and zooming and panning at all the way around the aircraft during takeoff cruise and landing. There was no CTD and I flew till 100nm away from OMDB at which point I disconnected Autopilot, landed and parked at OMDB complete with secure parking. I reached 35k ft cruise altitude and decided to turn on auto pilot for heading lock and altitude only. Set the fuel at 30000 kg and manually decided to fly the 777. This time I chose to start from the runway of okbk and loaded the 777 default panel state. I then closed P3d, rebooted the computer and followed the same process to start P3d as detailed above. Tried to fly again with settings un touched and default P3d.cfg and same CTD g2d.dll issue about 1 to 2 mins after turning on Autopilot.
#PMDG 777 COLD AND DARK DRIVER#
Used Guru3d Display Driver Uninstaller version 15.7.5.5 to clean out my nvidia drvier and reinstalled the 364.72 version. Googled g2d.dll error and based on online possible solutions and triedġ. The 777 LR and 300ER CTD occurs after about 1.5 minutes in the air once autopilot is tuned on.įaulting application name: Prepar3D.exe, version: 3.9, time stamp: 0x56df48ceįaulting module name: g2d.dll, version: 3.9, time stamp: 0x56df4993įaulting application start time: 0x01d1a04d6dd0de90įaulting application path: D:\Lockheed Martin\Prepar3D v3\Prepar3D.exeįaulting module path: D:\Lockheed Martin\Prepar3D v3\g2d.dll I then go through the configure and startup process and taxi manually till after take off and when I turn on the Autopilot mode when 500ft AGL. rte file for my flight and is then closed. PMDG 777 cold and dark panel is my default startup state. I change the airplane to PMDG 777 then select Airport / parking bay or runway and select ok
#PMDG 777 COLD AND DARK PLUS#
I run REX ESS PLUS then click Fly now which starts up P3d and opens the scenario page which has the f22 showing up by default. Simconnect working fine - Installed all versions including ESP Texture settings 1024 - so NO VAS issues whatsover! PFPX - latest build with NAVDATAPRO AIRAC 1604įollowed your setup recommendations as per PMDG-777-Introduction.pdfĬfg - only added FIBER_FRAME_TIME_FRACTION=0.01 & alwaysfullload=1 under MAIN Weather engine - REX ESS PLUS & REX4 TEX + soft clouds - completely updated Pilots - Vector & fs global ultimate series.
![pmdg 777 cold and dark pmdg 777 cold and dark](https://i.ytimg.com/vi/Tf6srPytbc4/maxresdefault.jpg)
![pmdg 777 cold and dark pmdg 777 cold and dark](https://i.ytimg.com/vi/SUB2rY101WY/maxresdefault.jpg)
Orbx - All products (including global, open LC and airports)
#PMDG 777 COLD AND DARK PRO#
Samsung SSD 850 PRO 1Tb for P3D + all addons including PMDG and orbx etc. Samsung SSD 950 PRO 512 GB nvme for W7 OS only Kingston HyperX FURY HX426C15FBK2/16 16GB Kit (8Gx2) DDR4 2666 Desktop RAM
#PMDG 777 COLD AND DARK INSTALL#
So no defrag policies or processes are in place.Īntivirus s/w is ESET nod 32 with my P3D install and addons d: drive excluded in Nod 32.Īsus Maximus Hero viii mother board - latest bios 1601ĬPU: i7-6700K 4.0GHz 8MB LGA1151 Skylake HT off in bios I followed Nick N's process for reinstalling and setting up W7 圆4 for a SSD based system. I was having PMDG 777 CTD issues soon after upgrading P3D from v3.1 to 3.2 and so decided to rebuild the entire PC.